Single-source Solutions

A single-source solution helps wetrooms to go the distance

By Carl Stokes, Head of Marketing, Schlüter-Systems Ltd.

There are so many elements to consider in the creation of a wetroom, in terms of both practicality and aesthetics. It must be fully waterproofed and able to cope with material movements, it must drain at the appropriate rate, it must project a certain image – be it vitality or tranquillity – and that’s before you even start to consider how your chosen products will work together.

It’s a finely tuned balancing act by anyone’s reckoning, but it doesn’t have to be difficult; a Schlüter®-WETROOM system not only contains all the items that you need for wetroom preparation and tile and stone finishing, but also eliminates compatibility worries, with all products having been designed to work together. The benefits of employing such a system can be felt across the construction chain. With your entire solution obtained from one source, troubleshooting and admin are easier, and there is a clear point of contact for any advice, aiding timely project progression at every step.

Proper attention to preparation and finishing enables a beautiful and long-lasting finish for an installation; for each problem you’ll need to address, Schlüter offers a targeted solution.

Problem: Guaranteed waterproofing provision for walls
Solution: Schlüter®-KERDI-BOARD and Schlüter®-KERDI-200
As well as being the death knell to an installation, water penetration can cause severe damage to the fabric of a building; poor moisture management can often result in the closure of rooms and loss of revenue, not to mention costly remedial works. To prevent this occurrence, it is essential to employ the appropriate waterproofing systems, installed beneath the tile or stone covering.

Schlüter-Systems offers an ideal solution to the creation of a CE Marked waterproof assembly for the walls of your wetroom installation: the tile backerboard, Schlüter®-KERDI-BOARD. There are a variety of backerboards on the market, but a number of them are merely water-resistant, requiring the installation of a waterproofing membrane in addition to the backerboard itself. By contrast, Schlüter®-KERDI-BOARD requires no additional finishing processes to make it waterproof, reducing two steps to one and saving considerable time on-site. To complete the assembly, joints are then sealed using waterproof sealing tape, Schlüter®-KERDI-KEBA, and sealant adhesive, Schlüter®-KERDI-COLL-L.

The light weight of Schlüter®-KERDI-BOARD does not compromise its strength and it is able to support up to 60kg per square metre, making it perfect for supporting all manner of tile and stone choices. With seven thicknesses available, ranging from 5 to 50mm, this backerboard is a multi-talent. While the boards at the thinner end of the spectrum are designed for use over existing substrates, latter thicknesses can be used as construction panels to create features such as shelves, partition walls and seats, allowing for unbridled freedom of design. Within the range there are also grooved boards for the creation of curved features, as well as preformed shower niches, and angle and U-shaped components for pipe panelling; all of which are designed for easy and targeted specification.

For situations that demand the use of a water-resistant board, Schlüter-Systems can provide the waterproof tiling membrane Schlüter®-KERDI-200, which can be laid over the board and sealed using the same easy steps as Schlüter®-KERDI-BOARD.

Problem: Preventing cracks in tile and grout, and providing guaranteed waterproofing for floors
Solution: Schlüter®-DITRA range

Cracking and debonding of tile and stone coverings are two of the most obvious problems encountered with wetroom installations and floor-level showers. They are incredibly common and are the most visually apparent symptom of an installation failure. However, with the use of a modern uncoupling system, these problems can be prevented.

Schlüter®-DITRA 25 is the unsurpassed uncoupling membrane for tile and natural stone installations, first entering the market in 1987. Its solid history, combined with its CE Marked waterproofing capability, has made it an incredibly popular choice worldwide for securing floor coverings within wetrooms.

Schlüter®-DITRA 25 is a patented polyethylene membrane with a grid structure of square cavities, each cut back in a dovetail configuration, and an anchoring fleece laminated to its underside. The tile adhesive mechanically locks into cut-back indentations on the topside of the matting, eliminating the need for additional anchoring mesh. This mechanical lock means that the adhesive does not adhere to the mat, avoiding the formation of a direct bond and allowing for independent movement.

The geometry of Schlüter®-DITRA 25 allows for the absorption of lateral movement in each direction. Through its unique two-layer design, this uncoupling mat truly separates the substrate and tile or stone covering by creating essential free space between the layers, in which the matting can move safely, reacting to the movement of the substrate and surface independently of each other.

Employment of Schlüter®-DITRA 25 as a waterproofing system for the floors of wetrooms and floor-level showers is easily achieved by carefully sealing the mat joints and connections with floors and walls using Schlüter®-KERDI-KEBA sealing band and Schlüter®-KERDI-COLL-L sealant adhesive.

Such has been the success of Schlüter®-DITRA 25, that specialist uncoupling solutions have been developed for particular applications. Schlüter®-DITRA-HEAT matting is an integral component of the electric underfloor heating system, Schlüter®-DITRA-HEAT-E, which allows for the creation of low-height and multi-functional heated surfaces. Schlüter®-DITRA-DRAIN is a combined uncoupling and drainage solution developed for exterior use, that ensures proper moisture management for balconies and terraces.

Problem: Ensuring adequate drainage slopes
Solution: Schlüter®-KERDI-SHOWER
The tile or stone covering in the shower area must be sufficiently sloped to allow for appropriate drainage and it should be noted that the flow of the showerhead must be less or equal to the flow rate of the drain. Falls in the floor gradient should be between 1 in 80 and 1 in 35. This is easily achieved with the prefabricated levelling and shower tray components of Schlüter®-KERDI-SHOWER, which are available with point or component linear drain systems.

Problem: Balancing practicality and aesthetics in drain design
Solution: Schlüter®-KERDI-DRAIN & Schlüter®-KERDI-LINE
In the point drainage system, Schlüter®-KERDI-DRAIN, the surrounding area falls at four points to a single point where the water flows away. The Schlüter®-KERDI-LINE linear drainage system offers an alternative solution, whereby water drains away via a channel length. Both systems are available in horizontal and vertical variants, with options to accommodate low assembly build-ups.

There are a number of modern grate and cover options available to complete the drain specification. For the ultimate finish with a continued field of tile or natural stone, Schlüter®-KERDI-LINE-D was introduced to the range. This offers a frameless covering support specifically designed for showers made from tile and natural stone.

Where the grate needs to act as a feature, there are a range of stainless steel designs available across both point and linear drains, including three new options introduced in Autumn 2017; Floral, Curve and Pure, from the new Schlüter®-KERDI-DRAIN-STYLE/-LINE-STYLE ranges, add yet more contemporary finishing possibilities to the specifier’s toolkit.

Drains of the Schlüter®-KERDI-LINE-G2 range comply with BS EN 1253, providing a constant 50 mm water seal and meeting flow requirements in compliance with National House Building Council (NHBC) regulations.

Problem: Auxiliary moisture management
Solution: Schlüter®-DITRA-HEAT-E
Wetrooms are ripe areas for the gathering of condensation which, if not dealt with effectively, can cause mould growth. Under-surface heating is an excellent addition to a wetroom, serving to dry out any residual moisture and provide additional luxury underfoot.

The problems that are encountered in tile and stone installations are exacerbated once heat is added to the equation; with the flooring assembly experiencing a greater range of temperatures, cracks in the tile or stone covering become all the more likely. For this reason, the uncoupling technology found in Schlüter®-DITRA 25 can also be found in the electric underfloor and under-wall heating system, Schlüter®-DITRA-HEAT-E.

As the system incorporates both uncoupling and underfloor heating, fewer layers are required in the flooring assembly. In contrast, a traditional system can require numerous products, including insulation board, underfloor heating mat, uncoupling membrane and encapsulation layers; all of which add height to an installation. Schlüter®-DITRA-HEAT-E-DUO – the latest iteration of the Schlüter®-DITRA-HEAT-E system – not only provides underfloor heating, uncoupling, bonded waterproofing, crack bridging and vapour pressure equalisation, but also offers thermal breaking and impact sound reduction of up to 13dB, courtesy of a special 2mm anchoring fleece on the system matting’s underside. The whole system comes in at only 7.5mm thickness, making it suitable for both new-build and renovation projects and saving considerable height within a flooring assembly.

Problem: Appropriate edge finishing
Solution: Schlüter®-PROFILES
When careful consideration has been made to the sanitary-ware, taps, shower, lighting and tile or stone covering in a kitchen or bathroom, the right choice of profiles gives that extra finesse. A strong palette of designs and hundreds of options for finishes, textures, materials and colours are available with Schlüter®-PROFILES.

Accessibility in wetroom design: providing access for all
A significant amount of time and thought is invested into the design of bathrooms for architectural projects. One design aspect that is important to consider is how our needs may change over time and the accessibility of the bathroom, especially for those with a disability.

This is where barrier-free bathrooms or wetrooms with floor-level showers, easy-access sanitary ware and the provision of seating areas can offer a practical, future-proof solution. It is always advisable to specify ceramic or natural stone tiles with a high slip resistance and with the huge range of tile and stone available today, creating luxurious, stunning, yet safe slip-resistant surfaces is easily achievable.

Learn more about specifying a watertight wetroom
The CPD seminar ‘Specifying Integrated Wetroom and Waterproofing Systems’ covers the key considerations in the design and installation of walk-in shower areas. Enhance and reaffirm your knowledge with this 45 to 60 minute presentation, held at your offices.

An integrated system solution, with products that are designed to work together, should be the specifier’s first choice when selecting products to use in shower areas and wetrooms. This provides the client with a single point of responsibility should any part of the system fail.

Key topics covered by the CPD seminar include: the benefits of an integrated system for wetrooms versus multi-manufacturer combined offerings, how point and linear drains can be hidden or accent the design, the requirements of waterproofing and how an integrated system offers peace of mind for a complete solution.

To book a CPD Seminar, call 01530 813396, email training@schluter.co.uk, or visit www.trainedwithschluter.co.uk.

Schlüter-Systems have dedicated consultants on hand to help with any stage of your specification project. For more information, call 01530 813396, email pr@schluter.co.uk, or visit www.schluter.co.uk.

NBS Clauses and BIM Objects for Schlüter-Systems Ltd are available on NBS Plus, National BIM Library and at www.schluter.co.uk.